品牌:其他 |
1.雷达回波面积大于40平方米,使用温度范围-35-55摄氏度,反射器边长470MM,总重量小于1.5KG,安装高度大于2M.
2.用于救生艇、筏及小型船艇的水上救援的雷达反射器,它包括一根金属材料的中心轴,在中心轴上、下两端套有四对轴套夹板环,每一对轴套夹板环上夹持固定有一片竖直安置的竖反射导电体,四片竖反射导电体通过上、下两端的定角环定位,其截面呈相互垂直的“十”字形,还有两片半圆形的横反射导电体,横反射导电体与竖反射导电体通过插槽插接在一起,两片横反射导电体即拼接成一个水平安置的完整的圆形,而竖反射导电体就与横反射导电体共同构成八个三面直角反射空间。本实用新型结构紧凑、合理,装拆、使用方便,反射面积大,反射角度幅度宽,不易腐蚀。
雷达反射器
雷达回波面积:≥40平方米
反射率:>95%
认可机构:CCS/EC
本产品RDF400角雷达反射器是配备于救生艇,救生筏。为增强小雷达目标回波的全向无源装置,它由每个导电平面互相垂直交叉而构成,平行于入射方向反射入射波的较大部分。其性能符合***化组织ISO8729:1997{E}的技术要求及国际海事组织IMO决议A-384{X}决议的规定。
主要技术指标:
1:反射面积 大于40M2 2:总重量为 小于1.6公斤
本产品有船检CCS证书!
此款产品的安装方法:
一、将反射器从包装袋中取出,将导电片围绕不锈钢转动轴展开向下、上8个直角三角形,而后将导簧销对准椭圆润孔插入再旋转90°锁住。(见图3、4、5).
Take reflection equippment out o packing bag.make the conducting flake surround the stainless steel rctating axis and outspread as 8 right-angle triangle up and down,then insert the spring pin into the ellpse hole and then screw by 90 °to lock(See picture 3、4&5)
二、将不锈钢转动轴中心内的一根不锈钢支杆拔出约20公分然后将塑料固定螺栓螺母旋紧。(见图6)
(2)Pull out a stainless beanpcle in the center of the stainless steel rotating axis by 20cm.then screwlight lastic bolt&nut(See picture 6)
三、将连接在反射器上的20公分支杆从救生艇筏顶蓬洞孔中插入阀体内,然后在筏体内再将其插入不锈钢升降支架中,***将升降支架上的全部塑料螺栓旋紧与筏低固定好即可。(见图7)
(3)Inset the 20cm long beanpole connected to refletion equippment to the hole on top sail of the raft,then insert it to the stainless steel up-and-down bracket in the body of the raft,at last screw tight all the plastic bolt & nut. make sure they firmly fixed to the bottom of the raft.(See picture 7)
四、建议安装高度:水平面2m
Propositonal installation height:2m from level
五、注意事项:Notice
(1)安装方法:避免阴影区。Installation Method:To avoid the shadoe area.
(2)罗盘的安全距离:2m。 Sfety Distance of Compass:2m.